Catégories
Chercher
Critères de recherche
Produits répondant aux critères de recherche
Motor shield V2.0 TB6612 et PCA9685 (Motor-shield-v2-TB6612)
- Fully compatible with interface extensions.
- Address can be modified through I2C and communication.
- It can connect 2 steering gear and output PWM drive directly.
- Up to 4 bi-directional DC motors
- Up to 2 stepper motors (unipolar or bipolar)
- 4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A for brief 20ms peaks) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC
- 2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution dedicated timer - no jitter!
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Tested compatible with Arduino UNO, Leonardo, ADK/Mega R3, Diecimila & Duemilanove. Works with Due with 3.3v logic jumper. Works with Mega/ADK R2 and earlier with 2 wire jumpers
Shield clavier LCD pour Arduino (oh-arduino-lcd1602keypad)
- 16x2 LCD & keypad shield for
- Utilizes the extremely common HD44780 parallel interface chipset
- Interface code is freely available
- uses 4 Bit For Arduino LCD Library
- Blue Backlight with white words (screen contrast adjustment)
- Reset button
- Its Up, Down, Left, Right buttons use only one analog input
- Size:8cm x 5.9cm - 3.15inch x 2.32inch
Arduino Easy Module Shield v1 (Arduino Easy Module Shield v1)
- Exemples d'utilisation (lien)
- Schéma (jpg)
- Compatible Arduino
- 2 boutons poussoir
- 2 Led (rouge et bleue)
- 1 Led RGB
- 1 récepteur infrarouge
- 1 capteur de luminosité - Photorésistance
- 1 capteur de température - LM35D
- 1 buzzer passif
- 1 potentiomètre rotatif
- 1 capteur d'humidité - DHT11
- 1 connecteur pour interface I2C
- 1 port série TTL
- 1 connecteur pour un signal analogique en lecture
- 1 bouton reset
Arduino Multi-function Shield (arduino-shield-multifunction-type1)
The multifunction shield features some most useful electronics divided into segments:
- Four LEDs
- Three pushbuttons
- A reset button
- A piezo-buzzer
- An LED display module (four-digit, seven-segment)
- Two serial LED display driver ICs(74HC595)
- A multi-turn trimpot (10K)
- A port for DS18B20 temperature sensor
- A port for TSOP1838 infrared receiver module
- A APC220 wireless module interface (serial/UART interface)
Module relais 10A (oh-module-relay-1-10A)
- Module relais à 1 canaux
- NO et NF
- Compatible Arduino
- Signal de contrôle de niveau 5V
- Indication de l’état par DEL
Module capteur avec microphone KY-038 (KY-038)
Le capteur KY-038 permet de détecter la présence d'un niveau sonore, ajustable via un potentiomètre.
- DO (Sortie numérique) : signal présent si la limite fixée par le potentiomètre est atteinte
- AO (Sortie analogique) : mesure directe de la tension à la sortie du micro
- L1 : Indique que le capteur est alimenté
- L2 : Indique qu'un son est détecté
Tension | 3.3Vdc à 5Vdc |
Bande de fréquence | 50 HZ à 20Khz |
Impédance | 2.2Kohms |
Sensibilité | 48 à 66 dB |
Dimension | 44 x 15 x 10 mm |
Arduino micro ATMEGA32U4 5V (oh-arduino-micro-atmega32u4-5v)
Ressources :
Microcontroller | ATmega32U4 |
Operating Voltage | 5V |
Input Voltage (recommended) | 7-12V |
Input Voltage (limit) | 6-20V |
Digital I/O Pins | 20 |
PWM Channels | 7 |
Analog Input Channels | 12 |
DC Current per I/O Pin | 20 mA |
DC Current for 3.3V Pin | 50 mA |
Flash Memory | 32 KB (ATmega32U4) of which 4 KB used by bootloader |
SRAM | 2.5 KB (ATmega32U4) |
EEPROM | 1 KB (ATmega32U4) |
Clock Speed | 16 MHz |
LED_BUILTIN | 13 |
Length | 48 mm |
Width | 18 mm |
Weight | 13 g |
Ressources :
Boitier pour Arduino (oh-arduino-case-clear)
- En acrylique transparent
- Compatible avec Arduino UNO
- 6cm x 7.5cm x 1.7cm
Arduino micro ATMEGA32U4 5V avec header soudés et câble USB (oh-arduino-micro-atmega32u4-5v-ASBLY-Cable)
Version assemblée (connecteurs soudés).
Câble USB de 80cm inclus
Ressources :
Microcontroller | ATmega32U4 |
Operating Voltage | 5V |
Input Voltage (recommended) | 7-12V |
Input Voltage (limit) | 6-20V |
Digital I/O Pins | 20 |
PWM Channels | 7 |
Analog Input Channels | 12 |
DC Current per I/O Pin | 20 mA |
DC Current for 3.3V Pin | 50 mA |
Flash Memory | 32 KB (ATmega32U4) of which 4 KB used by bootloader |
SRAM | 2.5 KB (ATmega32U4) |
EEPROM | 1 KB (ATmega32U4) |
Clock Speed | 16 MHz |
LED_BUILTIN | 13 |
Length | 48 mm |
Width | 18 mm |
Weight | 13 g |
Version assemblée (connecteurs soudés).
Câble USB de 80cm inclus
Ressources :
- 1